Forum Replies Created

Viewing 15 posts - 31 through 45 (of 63 total)
1 2 3 4 5
  • Author
    Posts
  • November 9, 2015 at 12:27 pm #15152
    mickattwo
    Participant

    There is a HONDA new plough on garden tractors section Ebay £75. It has the standard Honda rear hitch.

    November 5, 2015 at 9:32 pm #15080
    mickattwo
    Participant

    Hi I have a F 510 Honda which I use on a regular basis, I have a Howard 300/350 Plough that is adapted for my Honda using the pin on the rear hitch. I dont intend to use it, where are you, I am in Sheffield.
    Two weeks ago there was a Honda rear rotovator attachment £125 which is a fair price on Ebay.
    PM if you are interested in the plough (I may be going to Newark)

    September 28, 2015 at 10:04 pm #14663
    mickattwo
    Participant

    keep them coming v good mix of m/cs

    September 27, 2015 at 3:54 pm #14610
    mickattwo
    Participant

    WHAT IS THE PURPACE OF THE BOOTLACES, MINE WORKS OK AND HASNT ANY?

    August 7, 2015 at 6:15 am #13961
    mickattwo
    Participant

    Sorry to hear of your misfortune, they are so determined there is little that will stop them

    July 18, 2015 at 7:39 pm #13815
    mickattwo
    Participant

    Hi I have a Shay rototiller and a Shay rotogardener, not much difference but similar engine. I understand that the engine is Shay made and has a unique flywheel/timing setup. Both carbs look like Amal.
    I have instruction manualand a spare parts chart(no part numbers on the chart)
    I you PM me I will Photostat them for you
    I am missing a flywheel on one m/c the other is awaiting new points

    April 19, 2015 at 7:22 pm #12635
    mickattwo
    Participant

    Problem solved, the clutch was not disengaging fully. Thanks Charlie

    April 15, 2015 at 9:35 pm #12594
    mickattwo
    Participant

    My post should say Shay Rotogardener, I have all the paperwork and parts diagramsbut only Shay’s own part numbers. My problem may be the drive setup.

    March 29, 2015 at 8:37 pm #12338
    mickattwo
    Participant

    Charlie the inner cable is attached to the slide in the carb and wont come fully out. The carb is an AMAL the engine is Villiers from a Ransome 14 lawnmower. I do not know much about carbs but I understand that Villiers used several types on the same model engine.

    March 12, 2015 at 8:50 pm #12020
    mickattwo
    Participant

    I wish they were mine, very nice condition

    February 18, 2015 at 5:57 pm #11755
    mickattwo
    Participant

    If the plough used is vintage it should not be a concern if the power source is not. Is this correct?

    February 11, 2015 at 9:38 am #11636
    mickattwo
    Participant

    THERE IS ALWAYS A WAY ROUND PROBLEMS

    February 8, 2015 at 8:49 pm #11632
    mickattwo
    Participant

    GOOD TURNOUT AND GOOD WEATHER WELL DONE ALL ENTRANTS

    January 11, 2015 at 9:57 pm #11428
    mickattwo
    Participant

    Good pictures and a good day weatherwise and good ploughing conditions

    January 7, 2015 at 10:15 pm #11361
    mickattwo
    Participant

    My blacksmith friend says it is for knocking into brickwork etc and he has made 100’s in his time Ud for clothes linetc

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 63 total)
1 2 3 4 5