Horses and Garden Machines

September 12, 2019 in Machinery

Our journey this month takes us back to 1912 where labour was absolutely vital to keeping a country house spick and span both inside and outside. No self-respecting lady (or gentleman) would dare be seen without a couple of maids around the house keeping everything clean and smart whilst out in the gardens there’d be at least one struggling gardener faffing with the dahlias and doffing his cap for tuppence a week. 

The bigger the properties the more labour was required. And much like today tools and machinery could cut down on time-consuming tasks and save on labour costs.

These following machines are absolutely fantastic and one can see how modern machines have developed over the years. 

But we need a bit of labour to power the machinery and our time-saving saviour comes in the form of a horse, for horse powered equipment was really useful in a big country garden. So, gee up Dobbin, put yer boots on, we are going gardening.

Alternative Steel Horse Boot

Without his boots on poor Dobbin isn’t allowed on the posh lawns, or gravel driveway, in fact he isn’t allowed anywhere considered ‘delicate’ without being properly kitted out in footwear. We have no doubt all seen leather boots (image in the gallery) for ponies to stop them marking the grass when dragging a mower along. I’ve since discovered that metal horse boots were also available for the same reasons and they seem to be a curved metal plate with a Jubilee-type clip to attach them to the hoof. Available in several sizes, a quirk of ordering was that a drawing of the outline of the hoof (like drawing around your hand) was to be sent in with the order.

One of the main garden uses for pony-power (or horse) was for mowing lawns. The image below shows what appears to be a concerned gentleman trying to figure out the controls of his new 1912 combined mower AND roller, wonder if it came with a handbook to help the chap master all the levers and pedals? 

Horse drawn lawnmower

The mower can easily be adjusted for high and low cut, ‘throwing in and out of gear’ and ‘for raising the knives when passing over stones, rough places, or roads’. It can also be used for rolling with the high-speed cutters disengaged. Note that in the image the horse is wearing boots.

Horse drawn lawn sweeper

In 1912 the blokes ride-on mower, above, didn’t have the capability of grass collecting, although pedestrian mowers did. Yet at the same time lawn sweepers were available to be drawn by horses across the lawn as in the image on the right. That’s correct – horse drawn lawn sweepers; turns out they are not a new-fangled invention from the last 50 years as would be assumed.

The lawn sweeper shown had a large 3′ revolving brush and the collecting box could be emptied on the move – which presumably meant heaps of lawn sweepings in several places that some worker then had to clear up. The sweeper was designed to be used after the lawn had been mown to give a perfect finish and leave no grass clippings behind.

Horse drawn seeder

Another way to improve the lawn is to stick a bit more seed down. The lawn seeder, pictured right and called the ‘Velvet Lawn’ was useful for renewing or thickening grass and renovating bald patches on lawns. It would evenly distribute the seed and plant it at a reasonable depth according to how the operator adjusted the machine. The description of the machines workings is involved but it essentially cuts a slot with a revolving steel disc and drops grass seed into the slot before a roller covers it up – pretty standard stuff then.

So far our horse has been mowing, sweeping and seeding the lawns. There are three more garden jobs that can be done:

Horse drawn roller

There was a choice of garden lawn rollers. The basic one-horse affairs, which carried more of an agricultural look, could ‘smooth and keep in perfection, lawns, drives’ etc. The better two-horse rollers as shown in the image above were of superior quality and finish and were of a much more elaborate design with ‘attractively decorated woodwork’ above the roller and castings  – the desirable woodwork decoration making no difference whatsoever to the effectiveness of the rollers prime function, suppose it’s much like wood veneer in an Austin Allegro – but it’s a selling point.  

Horse drawn water sprinkler

The next innovation, as pictured on the right, is a water carrier and sprinkler with over 100 gallon capacity, for lawns, driveways and gardens. It can spread water up to 18’ wide or reduced down to 1’ wide as required. It can also be adjusted to apply one or two narrow streams of water onto vegetables or plants in rows. My question is: If one took a horse across said vegetable growing area dragging such a sprinkler, wouldn’t it be tricky to avoid the plants as there are four hooves, two wheels plus a mouth at the front end to manoeuvre through the crops?

And for the sprinklers encore – it is the only sprinkler adapted for spreading liquid manure as it will not clog. We are suitably impressed with this early interpretation of the slurry tanker.

Horse drawn turf cutter

Finally, an amazing machine that’d probably take some skill in using is a turf cutter. It cuts the turf to a uniformed width and thickness and to any length. There is an adjustable roller to regulate the thickness of the turf from half an inch to two inches. It will cut up to an acre a day saving the labour of 40 men. Yet it’s still to roll, lift, transport and re-lay. 

From a horses point of view I’m pretty sure the garden jobs would be preferable to pulling a plough through a field all day and being mostly in a garden pulling a mower or sweeper they’d be fair-weather jobs too. But, would they have their own horse, or did they just borrow a local one when required? Or horse-share even? Anyone know? 



These images are from a brochure we have in VHGMC archive. 

Everything for the Garden
. New York: Peter Henderson and Co., 1912. Henry G. Gilbert Nursery and Seed Trade Catalogue Collection. Special Collections, National Agricultural Library. 

https://specialcollections.nal.usda.gov/copyright-and-citation-guide


Note: Images/media are used for research/illustration purposes for non-profit only with copyright held by respective publishers where and as applicable.  

World of Chainsaws

August 15, 2019 in Machinery

Chainsaws

Old and vintage chainsaws are an interesting collectable item, some are highly prized and command serious prices. Yet chainsaws are something that folk browsing a display may not have considered or know much about. 

A question then: Off the top of your head can you name half a dozen chainsaws brands up to the early 1980’s that were sold in the UK? 

It’s a tricky question partly due to the fact that many chainsaw brand names don’t often relate to other machines such as mowers, tillers etc.

Here’s a quick run down of a few of the more common names that appear in the VHGMC gallery and archive: Clinton, Castor, Danarm, Echo, Frontier, Husqvarna, Homelite, Jonsered, McCulloch, Oregon, Oleo-mac, Pioneer, Partner, Poulan, Solo, Stihl, Sabre, Sachs Dolmar, Trojan, Teles, Tarpen.

And there are electric models including: Remington, Black & Decker etc. 

Some manufacturers produced both petrol and electric chainsaws. An advert from 1980 states that a free Mac 14 electric chainsaw (worth £72) would be given away with every purchase of a petrol McCulloch model – a case of buy one get one free. Perhaps the electric one was for Sunday best and being electric didn’t wake the neighbours from their weekend lie-in. 

Looking at newspaper archives over the last 40 years there are many articles about chainsaw safety. One says that “A chainsaw operator will have only one argument with a chainsaw and that could be his last” alluding to the fact that little appreciation of the power and speed of a chainsaw that could lead to potential damage and injury through lack of skill or attention. Which reminds me of a client who, many years ago and without any chainsaw skills, bought his first petrol chainsaw at a DIY store at a heavily discounted price because it lacked the box, instructions and safety info, thankfully he lived within spitting distance of the local hospital if anything had gone awry. 

There’s some positive chainsaw news too. In 1972 on the 29th November at 8pm there was a ‘Chainsaw owners and users chainsaw clinic‘ at the Talbot Hotel, Wexford, given by Bennett’s of Wexford. Bennetts were main dealers for Homelite and Stihl and would sharpen, service and repair any make. I have a feeling that the chainsaw clinic may have been well attended with people bringing in their saws which we now consider vintage – wonder what they all were?  

Allen Scythe with Tarpen Chainsaw

McCulloch were keen to get in on the act of promoting their saws. McCulloch (which most folk associate with budget machinery from some big retail shed) has had a varied history (B&D in 1974, Husqvarna from 1999, MTD from 2003) but in the 1960’s they were brilliantly promoting their chainsaw demonstrations. For example, one in Wexford in November 1965 which was ‘sure to attract a large audience‘ and another in 1970 at Potterton’s Cattle Market, Louth. which would appeal to farmers on a wet Friday in February and no doubt get some sales. 

Chainsaws aren’t always self powered items. Take the Tarpen chainsaw that could be driven by many machines via a flexi-drive as shown with the Allen scythe in the image, above. The Tarpen chainsaw also works with the Merry Tiller to make an interesting and useful machine see image or with the 24″ and 26″ Hayter rotary mowers see image.

Black & Decker 10″ and Flymo Partner 16″ vintage chainsaws

Many early and well-built chainsaws have probably survived – even if they have stopped working they were probably still thought of as too good to throw away and collected dust under the workbench instead. But the cheaper domestic end of the market has probably fared less well. These are the budget machines, where plastic overtakes steel and cast, and where the machines will after a few years become nothing but bin-fodder. 

In the right-side image and certainly aimed at the home gardener we have the 1981 Black & Decker 10″ chainsaw which will log, trim, prune and fell trees up to a very optimistic 20″ diameter. The blue 1100 watt saw was £29.99 and the orange 1200 watt saw £38.99. The yellow Flymo Partner 16″, 34cc, 2-stroke engine machine with 16″ cut felling trees up to 28″ diameter was £99.99. 

And what is surprising is that similar domestic machines can be bought today some 38 years later for similar prices, or in some cases less. 

Have a look at some proper-built chainsaws in the VHGMC Gallery. Have you got any to add?

New Club Website….

September 24, 2013 in Club News

After a year of planning, head scratching and considering many many options available, the new VHGMC website is here! This has been no easy task, in order to do everything that’s currently required, the website brings to you more options than ever before and makes this the one-stop place for all things relating to vintage horticultural machinery. 

Did I say one-stop? Well this is the place to organize your machinery photos or indeed videos all in your own galleries, create a group of friends, and also keep a timeline of what you are doing with your hobby. You can send messages to friends, comment on their updates, discuss topics in the forum and many other options. This keeps all your hobby related information in one easy place to share – rather than having it scattered across many website services. 

We have also added news articles to the site, so if you have something of interest them we can put it on there for you. And if you are wanting something extra to read then back issues of The Cultivator are available to download free for paid members.

Currently we have pushed the  technology as far as we can, in fact there are a couple of items I wanted to do but the solutions aren’t there yet! Although we do have many other things to add and try and you may notice some tell-tale signs on the site.  

If you have any questions then you can contact me at @alan (how brilliant is that? Just click on @alan and then click on ‘Private Message’  to the right of my avatar picture) or through the ‘contact’ page, there’s also some info about the website at tractorbox too. <

Tractor World 2013 Show Report

March 29, 2013 in Show Reports

Tractor World. by Charlie Moore.

Held over the weekend 2nd & 3rd March at The Three Counties Showground Malvern and organised by Tractor & Machinery magazine. The actual show organisation was carried out by a new team this year which saw a few changes to show layout and the introduction of displays of new tractors. Saturday had the usual auction by H J Pugh and on Sunday there was a vintage sort out. A couple of weeks before the show Martin Oldaker, editor of Tractor & Machinery, asked me if I would be willing to judge the horticultural section. For some reason I said yes, (must learn to stop saying yes). This worked out well as I was planning to visit the show on the Saturday anyway.  

1st Prize winner in the ride-on section. Neil Robinson with his Ransomes MG5

1st Prize winner in the ride-on section. Neil Robinson with his Ransomes MG5

Entries in the horticultural section were down on previous years, not helped by a number of horticultural machines appearing on other stands in the show. Entries were varied in both make and model as well as condition, with some as found and others fully restored. The full spectrum of eligible machines and tools was covered, from JALO to Trusty and Ransomes MG. Interesting exhibits included a very unusual single wheeled machine, believed to be a Howard and a good original condition Allman sprayer attachment on a Colwood motor hoe

Judging was very difficult due to the wide diversity of exhibits, I soon realised what a task it is and envy anyone that judges on a regular basis. Knowing some horticultural exhibits were not in the horticultural section I asked if they were to be included, as judging them would involve me walking around the whole show looking for them. The organisers confirmed only those in the horticultural section were to be judged. This was to cause some discontent as this was not clear on the entry forms. 

Results were as follows.

Ride on Machinery.

1st. Ransomes MG5, Neil Robinson.
2nd. Motostandard, Keith Hayden.
3rd. Cub Cadet, Ron Jaynes.

Pedestrian Machinery.

1st. Trusty Imp, Geoff Ravenhall.
2nd. Simplicity motor how, David Biggs.
3rd. Howard Demon, Henry Cawood.

Hand Tools.

1st. JALO collection, Pat Biggs.
2nd. Landmaster push how, Ivan Clark.
3rd. Jobu chainsaw, Mr Thomas.

Lincoln Steam 2012

March 26, 2013 in Show Reports

Written by Steve Woollas.

August seems so long ago but Lincoln steam, or to give the event it’s correct title The Lincoln Steam and Vintage Rally took place in glorious sunshine at the purpose built show site owned by The Lincolnshire Agricultural Society, adjacent to the A15 at Grange-de-Lings north of Lincoln on the 18th & 19th of August 2012.

Lincoln is the third in a trilogy of steam rallies held over the first three consecutive weekends in the eastern side of England commencing with Pickering, then Driffield, then Lincoln, and, for many a continual pilgrimage takes place to each in turn.

People travel far and wide to Lincoln and it was pleasing to meet club members who had travelled over from the Isle of Man for the event.

Lincoln steam appears to grow each year although the showground boundaries do not, and it is testimony to the organisers’ careful and strategic planning that all exhibits are accommodated within their allotted areas. This year the programme listed in excess of 1550 entries, including some of the 100 full size steamers, a further 100 miniature steamers and over 30 musical organs. Tractors amounted to 330 entries of which 50 fell into the horticultural category. with some 230 stationary engines, 28 awning displays, 130 entries in the models hall including 24 Meccano displays and in excess of 550 vintage/classic vehicles and a large trader market there has to be something at Lincoln for the whole family to view, admire and marvel upon.  
Allen Scythe fitted with a Villers engine. It is painted yellow because it spent it's working life on an airfield.

Allen Scythe MK2 fitted with a Villiers 11C engine. It is painted yellow because it spent it’s working life on an airfield.



Tractors have their own display area with a “drive through” parallel ring and paraded each day at 2pm lead by horticulturals and the commentary lasts for around 3 hours – not all by me you will be pleased to know!

First in the ring for the horticulturals was one of the nicest Fiddle Drills I have ever seen complete with instruction sheet attached to the body of the drill, along with a demonstration of how the march along in time with the hand movement when drilling, i.e one movement of the bow in time with each step forward. Another interesting item was a 1939 Vivian Lloyd Brush Cutter. One trusty steed was present and attached to the “working end” was an unusual Howard Rotavator attachment.  

I was interested to see some early versions of some machines present including a 1937 Ransome MG2 with the early Sturmey Archer T Type engine fitted, the 1941 allen Scythe MK2 (pictured) fitted with the Villiers 11C engine, finished in yellow livery as this machine spent it’s working life on an airfield. Cliffords were well represented with two Clifford Juniors in the line up, as were Ransomes with examples of MG2, MG5, MG6 and MG40. A 1951 Monrotiller Series One in original paint and transfers made an interesting item in the Parade as did in total contrast a nicely restored 1951 Bolens with cultivator in green and yellow. 

Note: This article has been reproduced and edited from the November 2012 issue of The Cultivator and written by Steve Woollas. 

Ride On Machines

March 25, 2013 in Machinery

Trusty-tractor

There are many ride-on machines and garden tractors available such as this Trusty Steed dating from around 1950

Popular with collectors, enthusiast and exhibiters are ride-on machines. The most common are the garden tractor or ride-on mower types but there are many others too such as tracked crawlers like the Bristol, the three wheeled Gunsmith and the Opperman Motocart.

Whether you are collecting a machine for preservation, restoring & showing or to use on the horticultural plot there are machines ranging from the 1920’s through to the 1990s.

Some of the more common garden tractors of the ride-on mower types which tend to date from the late 1970’s onwards are Atco, Westwood, Roper and Mountfield to name just a few. Many of these lower-spec machines were aimed at the weekend gardener with a large lawn to mow and occassional trailer work. These entry-level tractors often had ‘bigger brothers’ with more power and capabilities.

More robust garden tractors capable of serious work such as pulling a plough on an allotment, powering a rotavator and snow clearing work include well-known brands like the American Wheel Horse tractor range (1950’s -90’s) and the 1960’s UK Martin-Markham garden tractors. These tractors and others which are suitable for ploughing are also great for horticultural ploughing events which VHGMC members can take part in at various locations.

Ransomes Crawler & Bolens Ride-a-matic

Ransomes crawler and Bolens Ride-a-matic working the ground at a ploughing event

Through the decades demand and innovation has created many diverse machines tailored for specific jobs. Machines such as the David Brown 2D (1955-61) that can be used with numerous implements like cultivator tines, a row thinner and a reversible plough – an ideal machine for crop and open field work. Another machine is the 1950’s Scottish designed Rollo Croftmaster, created for working on Scottish small holdings up to 10 acres in size, this is a compact yet substantial four-wheeled tractor.

Bonser truck

Bonser truck from the 1960’s. In excellent restored condition at a show.

Out of the field and into the yard, still classified by the VHGMC as ride-on machines there are a varied range of trucks available. Some with timber bodied rear loading areas and some with tipping bodies too. The three-wheeled Wrigley motor truck (1930’s onwards) and the Bonser truck are two well known makes and always make a good exhibit at a show.

Popular with the tracked crawler users are the Ransomes MG2 and the later MG5. These can often be seen at shows and ploughing events. Also in the ride-on-machines category are the Bristol tracked crawlers.

Many enthusiast tend to collect one or two makes of specific machines and as well as the machines themselves they will collect literature, original brochures and price lists for their specific machines. This makes a collector a very valuable source of knowledge and very helpful advice.

Walk Behind Machines

March 25, 2013 in Machinery

2012-11-10-1076

A collection of Landmaster motor hoes being shown with various attachments.

The range of pedestrian-controlled machinery is certainly extensive and it is all covered by the VHGMC. Whether it was built in the 1920’s or the 1990’s it is all the same to us.

The walk-behind category is probably the largest one in the club and encompasses everything from the humble cylinder lawn mower to the larger Iron Horse type tractors that compete at ploughing matches.

Now that insecticide sprays are widely used in agriculture the motor hoe has completely disappeared, yet these were widely used in the 30’s, 40’s and 50’s to combat weed infestations and these remain one of the main collectible machines of our club members. They are generally light and easily transported yet very eye-catching, and were always painted in bright colours to increase their appeal.

Walk behind machines are excellent for showing or using.

Walk behind machines are excellent for showing or using.

Another favourite of collectors is the rotavator that has been used on allotments since it’s invention in the 1950’s and is still a firm favourite today, with manufacturers varying from Atco to Wolseley with every company in between.

The appeal of this machinery is that the collector can restore it using very few tools and in a very small workshop. It is generally inexpensive to buy and is widely available, and when the restoration is finished the restorer can use it at many of our club working events so that the work is never finished when the restoration is complete. You can actually play with the finished article, or even use it for what it was deigned to do originally – assist in growing food.

Hand Tools

March 25, 2013 in Machinery

Vintage hand-tools covers more than just a collection of garden shears or grandad’s pre-war spades and forks in the allotment shed.

There is a vast and eclectic range of tools, powered by electric, petrol or human power. Although the term hand-tools tends to automatically refer to smaller items like shears used in the garden it does also cover a broader area including pushed hoes, garden sprayers, insecticide dusters and lawn edgers to name just a few.
Garden sprayers

An excellent and interesting display of garden sprayers. These are all hand-powered with some being small for domestic garden use and around the greenhouse and the larger wheeled versions for larger application or commercial use.


This is a fascinating and growing collectors area where superb collections of items can, mostly, be gathered relatively easily. These are sometimes exhibited or displayed as a group of items such as secateurs through the decades, or perhaps as a collection produced by a single manufacturer such as the 1960’s range of Black & Decker hedge-trimmers. These displays of hand-tools appeal to the viewing public who can often remember using them or recall their grand-parents having them many years ago.

Collecting hand-tools can be a great hobby especially when one has a manufacturers brochure or a catalogue and the challenge is on to find the one elusive item advertised!

Many vintage hand-tools in the UK were made by UK companies rather than being imported from the US or Europe. So it is very easy to find UK engineered items at vintage auctions or even car-boot sales.
Secateurs

A selection of secateurs and cutting tools


Some of the most well known companies in the UK are Jalo (push hoes), Sheen of Nottingham (flame guns), Fisons, and Sisis (both making lawn fertiliser spreaders in the 1950’s & 60’s), There is quite a long list of manufacturers and a wide range of products they manufactured too.

Although there are many Uk manufacturers there are US manufacturers that imported their tools into the UK like the Planter Junior company . Their wooden-handled hoes were incredibly popular and sold in huge numbers from the 1930’s onwards. Some of their hoe models were available with a small plough and a seeder too. These are collectible, can be found quite easily and make a good exhibit.

Most hand-tools are items in their own right but some hand-tools can be attachments or additional to a much larger machine. For example the Wolseley Merry Tiller had attachments which could include a hedge trimmer and chainsaw – both of which worked via a flexi-shaft from the Merry Tillers petrol engine. Similar items were available for other makes too such as an electric-powered hedge-trimmer running from an Allen scythe and the range of implememts manufactured by the Tarpen company.